| Motorcycles and Twowheelers: Bike maintenance - "Motorcycle Belt Tension Inspection, Belt and Wheel Alignment" Wednesday, 20 August, 2008 | Home | Suggest a Link |
Formula 1 Fantasy LeagueI strongly believe that knowledge is power. Especially when it comes to motorcycle maintenance. Why go to the stress and expense of having your local motorcycle shop perform your maintenance and upgrades when you can learn to do it yourself? And you know that if you do your own maintenance, that you will give the extra attention required to do a competent job. I doubt you can say the same for the underpaid and over-worked motorcycle service mechanic.
The other benefit of doing your own motorcycle maintenance is that you learn more about your bike. This has many benefits. You will be able to tell when something is not running right. Also, you will have the skill set to get yourself out of any situation where you find yourself broken down miles away from town. Besides, just wrenching on your bike is a total Zen fun motorcycle event.
In this set of motorcycle knowledge base instructions, we focus on doing a motorcycle drive belt inspection, followed up by a drive belt tension adjustment and belt and wheel alignment.
With the majority of cruiser motorcycles now running with drive belts over chains, learning how to do your own belt adjustment is essential. Plus it is a far less messy task than performing maintenance on a chain. This instruction assumes the reader has some natural basic motorcycle wrenching talent. I believe most people can learn these tasks but there are some that may be out of their league and have no mechanical talent. For these people, please step away from the tools and let your certified mechanic perform any maintenance and upgrades.
This instruction is performed on a Victory Kingpin motorcycle. This Victory Kingpin motorcycle, like the rest of the Victory motorcycle models, has a right-side belt drive. The major pain of the Victory design is that you have to remove the exhaust or Slip on canisters to get at the right-side axle. This is only if you intend to remove the axle and wheel (Mainly used to remove the wheel and take it to the shop to mount new tires. The best way to save lots of money when replacing tires). This will be discussed in another maintenance instruction. Otherwise the motorcycle service shops will charge you their hourly rate to store the bike, remove the wheel and remount. Not cheap. Removing the wheels yourself makes it so you only pay for the mounting and balancing. Another tip, buy your tires online to save even more money.
Are you ready? Let's get started. For the Drive Belt Inspection it is recommended that you inspect the drive belt annually, and replace at specified intervals, regardless of belt condition.
To perform the actual belt tension inspection, perform the following:
Before you do the Belt Tension Adjustment, you need to make sure the wheel alignment is correct. The following with give you instruction and tips on aligning the wheel and belt correctly.
First measure from the center of the swingarm pivot to the center of the axle. Keep it the same on each side. I have been doing this on dirt bikes for many years and it has not failed yet. I use the Motion Pro belt tensioning tool.
This is what I do if I change a tire or belt.
At this point I test ride. I have NEVER had to go back and readjust doing it this way,and I have done MANY without a tracking problem. No strings or tape necessary.
Many years ago when I got hooked by motorcycles, I started to hear a lot about two and four stroke engines... It seemed there were (and there still are) strong opinions in pro and con of each of the engine types.
As Internet wasn't available, and as I was worried about other aspects or motorcycle riding back then, I left that question unanswered for a long time.
If this is your case or if you are interested in these two kinds of internal combustion engines, in the next few lines I hope to give you a few fast answers and some resources
Read this article in full
The amp/hour (AH) capacity is the basis for rating motorcycle batteries. For example, a 12AH battery can produce one amp of current flow for 12 hours, or two amps for six hours. In order to calculate the amount of time needed to use up a fully charged motorcycle battery by turning the lights on, we have to take power in watts, and divide it by voltage, which gives us the current draw in Amps. Therefore, a 72 watts beam and tail together, divided by 12 volts equals a 6-amp draw. So in 2 hours, the 12AH
Read this article in full
The tachometer or the rev counter tells the speed of the engine of the motorcycle in revolutions per minute (RPM). Common nowadays are electronic rev counters that can be installed by the dealers you get them from. But for used motorcycle parts, rev counters usually come in just any wrapping without instructions or diagrams. In cases like these, you may install your rev counter with the following instructions to help you.
The very first step is to move the headlight away. This is a great help later on in avoiding some mistakes and will definitely help you finish faster. If you
Read this article in full
The most common types of bearings are wheel bearings. Motorcycle wheels have them, so do skateboards. The bearings help give you a smooth ride.
It was no less than Renaissance man himself, Leonardo Da Vinci who described a type of wheel bearing in his studies in the beginning of the 16th century. The invention of the wheel bearing, alongside the other inventions of the rebirth, is one of the most significant heirlooms of the era that have changed little over time. Leonardo da Vinci is said to have described a type of wheel bearing around the year 1500.
If you're wondering what
Read this article in full
You may ask yourself, what is a motorcycle fork stabilizer and why do I need one for my motorcycle? These are very reasonable questions to ask, especially since you have expected the motorcycle manufacturer to have given your motorcycle the highest performance suspension components available. I hope to answer these questions and many more within this motorcycle fork stabilizer article.
I first became aware of motorcycle fork stabilizers from the
Cycle Solutions (www.CycleSolutions.net) motorcycle
forums. Several members of the forum suggested that this was an
aftermarket part to install on your motorcycle. Being both
curious and ignorant I asked questions. Is this
Read this article in full
 |  |  |  |  |
